Build thread for dog shelter campaing

[Jyri Haveri]

Third belly plaited.

Here is the drop to the handle. I think the overlay will be 14-18 plat but handle will be 12plat. This should produce nice step between the transition and handle. I have something in my mind for that.

[Jyri Haveri]

https://youtu.be/mDZpV4iC1W8
I took it out of the vise, gave it first roll and tested it. I tryed to do this as honestly i could but with waxed thread the handle was a bit slippery. It went quite well keeping in mind that it is really fresh and the strands are yet to be binded to the core.
This whip, until this point at least, is one of the most uniform whip i have produced and by this i mean the difference between the back and frontside.

Next: more binding..

[Ron May]

That is looking really good Jyri.
I'm not understanding the long strands at the end of the handle though.
It seems like a waste of cord. Perhaps you could explain it.
Is that orange thing by your hand in the second picture a staple?
Nice job on the roll out.
This is going to be a really good whip.

Ron

[Jyri Haveri]

Thanks Ron!
That orange thing is waxed thread wich got stuck in the plaiting from second belly.

When i plait i think it is better to have some ecsess cord than not enough.
I have played between doubling the lenght and going 1,5 times the lenght i'm going to plait but i have yet to find right way.
I leave them like that so when i finish the next layer i can plait over those those strands beyond the handle so its easier to finish neatly without the need to cut the handle.

[Jyri Haveri]

And i usually double only the first 4 and the rest i just measure 1,5times the lenght i still have to plait.

[Mark Elliott]

That whip is looking very nice, Jyri.

[Robert Gage]

Jyri, those dogs are wagging already!

[Scott A. Cary]

Nice work, Jyri!

[Jyri Haveri]

Thanks!


Binding in progress..

[Ron May]

Looking good Jyri.

Ron

[Jyri Haveri]

So i got overlay done when i was in nightshift buuut..
There is a slight twist in it and some minor gapping. I have not rolled it wich could make that go away but then it would be harder to replait it.
I'm going to play it safe and take quite a bit apart and plait it again and add 2 strands to it.
It is possible that i have to take it all apart but i want to make this a good one.

[Mark Elliott]

Jyri, It's tough trying to measure up to this crowd, isn't it?

[Jyri Haveri]

Yup, but in a good way

[Ron May]

Jyri, from the photo it looks like it's fairly straight.
But you are right. It looks like you need to add a strand or two.
I like that color.

Ron

[Robert Gage]

The quest for perfection is always rewarding! That's an admirable attitude, Jyri!

[Georg Ernst]

Great idea of you with the core, I should try that, and thanks for the documentation how you make the whip.

[Jyri Haveri]

Thank you!
Georg, if some whipmaker is lucky enough to win this and have some pointers for me it is easier to find possible mistakes this way
I ordered some battlecord for future project and i am going to use some of that for next builds core. Same as this one but with 2 more layers on the core.

[Jyri Haveri]

I took the overlay apart and rechecked the core
https://youtu.be/3X3cf_T4zzI


Core is fine but i gave it some more binding right after the handle, just in case.

I plaited the overlay again and i'm almost done but so is my hands.

I should get the overlay done tomorrow, i hope.

[Robert Gage]

That's looking very good, Jyri!

[Ron May]

You're doing a really good and through job of it.
It rolls out very nicely.

Ron