Whip #3

Le'me see... Whips, whips and - whips!
Post Reply
User avatar
Ron May
Member
Posts: 13336
Joined: Thu 24. Sep 2015, 23:57
Location: McAllen, Texas

  Whip #3

Post by Ron May »

Whip number 3 is mostly done.
Just needs the heel finished and waxing.
The end is done in a fall loop so falls can be changed when ever desired.
I like the way Tyler can change falls on his whips using the English Eye, and wanted something
similar. I used this ending on Blue Lightening and liked it a lot so I added it to this snake whip.

It's a 4' foot 2 belly 16 plait Snake whip which was made for a friend out of left over cord from W2.
All that is needed to finish the whip is the knob I ordered from Roy's Whip Nation.
It's going to be a concalco alves knob.

Ron

Image
It's ok if you disagree with me.
I can't force you to be right.
Top
User avatar
Ron May
Member
Posts: 13336
Joined: Thu 24. Sep 2015, 23:57
Location: McAllen, Texas

 

Post by Ron May »

I forgot to mention that it's shot loaded to 1 1/2' with a tapered twisted core after that.

Ron
It's ok if you disagree with me.
I can't force you to be right.
Top
User avatar
Rachel McCollough
Member of the Ring
Posts: 9864
Joined: Tue 21. Apr 2015, 11:37
Location: South Mississippi, USA
Contact:
Contact Rachel McCollough

 

Post by Rachel McCollough »

Nice looking whip, Ron, you should be very proud. That's going to really look great with that wood!
Inch by inch.
Top
User avatar
Ron May
Member
Posts: 13336
Joined: Thu 24. Sep 2015, 23:57
Location: McAllen, Texas

 

Post by Ron May »

Thank you Rachel. :)

Ron
It's ok if you disagree with me.
I can't force you to be right.
Top
User avatar
Craig Frank
Member
Posts: 1233
Joined: Thu 23. Jul 2015, 21:06
Location: Arizona

 

Post by Craig Frank »

Ron - very clean looking pattern. I see a slight hinge, but I doubt it will affect the handling. All of mine have at least one hinge towards the end.
If I can't run fast, I'll make slow look impressive.
"By the power of ibuprofen!"
Top
User avatar
Ron May
Member
Posts: 13336
Joined: Thu 24. Sep 2015, 23:57
Location: McAllen, Texas

 

Post by Ron May »

Thanks Craig. :)

Ron
It's ok if you disagree with me.
I can't force you to be right.
Top
User avatar
Robert Gage
C Member
Posts: 13353
Joined: Fri 7. Feb 2014, 15:58
Location: UK

 

Post by Robert Gage »

Well done, Ron! A good taper. As Craig says, a very clean-looking pattern - and I think it will look even better when it's been waxed. That's a neat little eye to attach the fall and cracker. Altogether nice! :)
'Less is often more!'
Top
User avatar
Ron May
Member
Posts: 13336
Joined: Thu 24. Sep 2015, 23:57
Location: McAllen, Texas

 

Post by Ron May »

Thank you Mr. Robert. :)

Ron
It's ok if you disagree with me.
I can't force you to be right.
Top
User avatar
Ben Varsek
Member
Posts: 2446
Joined: Mon 4. Apr 2016, 16:26

 

Post by Ben Varsek »

@ Ron May:

Great Job - I am sure your friend is going to love her new whip !!!
I realy like the "english eye" fall hitch that you have put on this whip (and on the "Blue Lightning" whip) and your plaiting looks very good as well !!!

Thank you very much for sharing !!!

All the best
Ben
Top
User avatar
Ron May
Member
Posts: 13336
Joined: Thu 24. Sep 2015, 23:57
Location: McAllen, Texas

 

Post by Ron May »

Thank you Ben. :)

Ron
It's ok if you disagree with me.
I can't force you to be right.
Top
Bobbi Holyoak

 

Post by Bobbi Holyoak »

Wait! This went really fast! Great job!
Top
User avatar
Ron May
Member
Posts: 13336
Joined: Thu 24. Sep 2015, 23:57
Location: McAllen, Texas

 

Post by Ron May »

Thanks Bobbi. :)

Ron
It's ok if you disagree with me.
I can't force you to be right.
Top
User avatar
Jessie Edwards
Member
Posts: 5763
Joined: Thu 11. Jun 2015, 19:00
Location: Wisconsin, USA
Contact:
Contact Jessie Edwards

 

Post by Jessie Edwards »

Whoa! That did go fast! You animal!
Due to rising costs, dirty deeds are no longer done dirt cheap.
~Management
Top
User avatar
Ron May
Member
Posts: 13336
Joined: Thu 24. Sep 2015, 23:57
Location: McAllen, Texas

 

Post by Ron May »

Thanks Jessie. :)

Ron
It's ok if you disagree with me.
I can't force you to be right.
Top
User avatar
Ron May
Member
Posts: 13336
Joined: Thu 24. Sep 2015, 23:57
Location: McAllen, Texas

 

Post by Ron May »

Here's the heel knob I am fixin' to put on with some Loctite Epoxy .

Image

Image

I don't use the word gorgeous much but that's what this knob is.

There will be more photos after I have installed it.

Ron
It's ok if you disagree with me.
I can't force you to be right.
Top
User avatar
Rachel McCollough
Member of the Ring
Posts: 9864
Joined: Tue 21. Apr 2015, 11:37
Location: South Mississippi, USA
Contact:
Contact Rachel McCollough

 

Post by Rachel McCollough »

It sure is! Going to look fantastic!
Inch by inch.
Top
User avatar
Ron May
Member
Posts: 13336
Joined: Thu 24. Sep 2015, 23:57
Location: McAllen, Texas

 

Post by Ron May »

It's on.
It feels fantastic in the hand. :)
I may never tie a turks head heel knot again. :) (just kidding)

Image

Image

Ron
It's ok if you disagree with me.
I can't force you to be right.
Top
User avatar
Jessie Edwards
Member
Posts: 5763
Joined: Thu 11. Jun 2015, 19:00
Location: Wisconsin, USA
Contact:
Contact Jessie Edwards

 

Post by Jessie Edwards »

I don't get to say "nice knob" often, but when I do....I raise my eyebrows and wink suggestively.
Due to rising costs, dirty deeds are no longer done dirt cheap.
~Management
Top
User avatar
Ron May
Member
Posts: 13336
Joined: Thu 24. Sep 2015, 23:57
Location: McAllen, Texas

 

Post by Ron May »

Jessie, :)

Ron
It's ok if you disagree with me.
I can't force you to be right.
Top
User avatar
Rachel McCollough
Member of the Ring
Posts: 9864
Joined: Tue 21. Apr 2015, 11:37
Location: South Mississippi, USA
Contact:
Contact Rachel McCollough

 

Post by Rachel McCollough »

Ha! Jessie!

Now that's very well done, Ron-Gator great job! Looks great, Ron!
Inch by inch.
Top
Post Reply

Return to “Whips (+++ public thread +++)”